{"product_id":"ce-lf6400e48-currie-enterprises-hd60-high-pinion-front-axle-w-4-88-gears-and-e-lockers","title":"Currie Enterprises HD60 - High-Pinion Front Axle w\/ 4.88 Gears and E-Lockers","description":"\u003cp\u003eThe Currie HD60 high-pinion front axle for the 2018 and newer Wrangler JL delivers next-level strength and reliability. The HD60 features a massively reinforced rotated 60 series center section, 3.5-inch tubes, chromoly axles, and heavy-duty forged JL inner knuckles. Upgrade to an HD60 and start enjoying your off-road adventures without the worry of frontend failure.\u003c\/p\u003e\n\u003cp\u003eDetails:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e68 in. Stock JL Rubicon Width (+1.5 in. Over Non-Rubicon Models)\u003c\/li\u003e\n\u003cli\u003eHD60 High-Clearance Center Section with Rotated Cover Improves Obstacle Slide-Over\u003c\/li\u003e\n\u003cli\u003eHigh Volume Flow-Thru Pinion Oiling System Keeps Bearings Bathed in Cool Oil\u003c\/li\u003e\n\u003cli\u003eRock Slider Low-Friction Skid Plate Glides Over Rocks\u003c\/li\u003e\n\u003cli\u003e3.5 x .375-inch DOM Axle Tubes are Twice the Strength of the Stock Tubes\u003c\/li\u003e\n\u003cli\u003eCurrie Chromoly 35-Spline Inner and 32-Spline JL Outer Axles\u003c\/li\u003e\n\u003cli\u003eCurrie Heavy-Duty Forged JL Inner Knuckles\u003c\/li\u003e\n\u003cli\u003eChoice of Eaton ELocker or ARB Air Locker\u003c\/li\u003e\n\u003cli\u003eChoice of 4.56, 4.88, 5.13, or 5.38 Gear Ratio\u003c\/li\u003e\n\u003cli\u003eCurrie Heavy-Gauge Laser Cut Brackets\u003c\/li\u003e\n\u003cli\u003eUpgraded 1350 Pinion Yoke\u003c\/li\u003e\n\u003cli\u003eCurrie Rock-Proof Nodular Iron Differential Cover\u003c\/li\u003e\n\u003cli\u003eSatin Black Powder Coat Finish For Long Lasting Protection\u003c\/li\u003e\n\u003cli\u003eRetains the Vehicle's Stock Outer Steering Knuckles, Brake Assemblies, and Wheels\u003c\/li\u003e\n\u003cli\u003eRequires Aftermarket High-Clearance Tie Rod Assembly (see note below)\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThe HD60 high-pinion axle for the 2018 and newer Jeep Wrangler JL features heavy-duty brackets and mounts in the stock location for a direct bolt-in fit. The vehicle's factory outer steering and brake components must be transferred to the HD60 to complete the assembly. A high-clearance aftermarket tie rod is required (see notes below). The vehicle's factory driveshaft will require modification or replacement to accommodate the larger 60 series housing and 1350 series u-joint\u003c\/p\u003e\n\u003cp\u003eCurrie HD60 Features:\u003c\/p\u003e\n\u003cp\u003eHD60 high-pinion nodular iron center section is simply the strongest 60 series casting we offer, with heavier main caps, ARP® main bolts, and additional reinforcement in critical areas                    \u003c\/p\u003e\n\u003cp\u003eHD60 high-pinion radius bottom center section delivers unmatched ground clearance, and improved obstacle slide-over by presenting a smooth curve rather than the sharp leading edge found on other 60 housings\u003c\/p\u003e\n\u003cp\u003e Replaceable AR400 hardened steel skid plate resists deformation and gouging to slide over obstacles far better than iron housings or mild steel plates\u003c\/p\u003e\n\u003cp\u003e Large diameter outer pinion bearing (right) is designed for the demands of reverse rotation\/high pinion housings. Stock low pinion bearing (left)\u003c\/p\u003e\n\u003cp\u003e High volume flow-thru recirculating oil system keeps pinion bearings bathed in cool oil, reducing operating temperatures and eliminating oil starvation issues\u003c\/p\u003e\n\u003cp\u003e Large 3.5 in diameter .375 wall axle tubes (left) are twice as strong as the factory tubes without being overweight or sacrificing ground clearance\u003c\/p\u003e\n\u003cp\u003e Upper control arm mounts feature rebuildable Johnny Joints® for maximum suspension articulation with unsurpassed durability\u003c\/p\u003e\n\u003cp\u003e Super strong Currie nodular iron front cover protects expensive internals, adds structural support to the housing's face flange, and locates the driver’s side upper control arm mount\u003c\/p\u003e\n\u003cp\u003e Lower control arm mounts are one-piece construction with integrated skid plates to help fend off bracket seeking rocks\u003c\/p\u003e\n\u003cp\u003eSpecifications:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003ePowder Coat - Black satin powder coat finish adds long-lasting protection against rust and corrosion to keep your HD60 looking its best\u003c\/li\u003e\n\u003cli\u003eHousing - HD60 high-pinion nodular iron radius bottom center section with   hicker walls and webbing\u003c\/li\u003e\n\u003cli\u003eBearing Caps - Increased cross section nodular iron caps secured with ARP® fasteners\u003c\/li\u003e\n\u003cli\u003ePinion Bearing - Large diameter front pinion bearing matched to rear bearing\u003c\/li\u003e\n\u003cli\u003ePinion Oiling High volume flow-thru recirculating oil system\u003c\/li\u003e\n\u003cli\u003eGear Set - Dana 60™ reverse rotation thick gear sets (compatible with super 60 reverse cut gears)\u003c\/li\u003e\n\u003cli\u003eDifferential Carrier -          Standard Dana 60 4.10 and down differential carriers with thick ring gears for all gear ratios\u003c\/li\u003e\n\u003cli\u003ePinion Yoke  - 1350 u-joint\u003c\/li\u003e\n\u003cli\u003eSkid Plate - AR400 hardened steel skid plate\u003c\/li\u003e\n\u003cli\u003eDifferential Cover - Currie nodular-iron cover, Red\u003c\/li\u003e\n\u003cli\u003eAxle Tubes - 3 .5 inch diameter x .375 wall DOM tube\u003c\/li\u003e\n\u003cli\u003eAxles -            Currie Chromoly 35-Spline Inner and chromoly 32-Spline JL Outer Axles\u003c\/li\u003e\n\u003cli\u003eEnd Forgings - Currie JL\/JT heavy-duty forged steel inner C’s\u003c\/li\u003e\n\u003cli\u003eSteering Knuckles - Accepts the vehicle's factory steering knuckles\u003c\/li\u003e\n\u003cli\u003eBrake Rotors - Accepts the vehicle's factory front rotors\u003c\/li\u003e\n\u003cli\u003eBrake Calipers - Accepts the vehicle's factory front calipers\u003c\/li\u003e\n\u003cli\u003eTie Rod - Accepts the vehicle's factory tie rod\u003c\/li\u003e\n\u003cli\u003eSuspension Brackets - Heavy gauge 3\/16 inch steel mounting brackets\u003c\/li\u003e\n\u003cli\u003eControl Arm Mounts - Johnny Joints® installed with greaseable bolt\u003c\/li\u003e\n\u003cli\u003eGeometry - Optimized for stock height up to 4 inch of lift\u003c\/li\u003e\n\u003cli\u003eTrac Bar Mount - Ram mounting brackets welded to housing, setup for PSC 8” travel steering ram (not compatible with stock steering stabilizer)\u003c\/li\u003e\n\u003cli\u003eWidth - 68-inch stock Wrangler JL Rubicon width (1.5 inches wider overall than non-Rubicon models)\u003c\/li\u003e\n\u003cli\u003eFinish - Black satin powder coat\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNotes\u003c\/p\u003e\n\u003cp\u003eTie Rod: The HD60 housing requires the use of a high-clearance aftermanket tie rod to prevent tie rod\/housing interference at full turn. JL Rubicon\/JT compatible high-clearance tie rods are available from Steer Smarts (Yeti XD P\/N 78088001)\u003c\/p\u003e\n\u003cp\u003eABS Sensors - This does not include ABS sensors, the factory sensors from the stock axle must be retained and installed on the Currie housing\u003c\/p\u003e\n\u003cp\u003eComputer Programming: Vehicles require a computer programmer to reset the gear ratio and tire height in the vehicle's computer for the proper function of the vehicles stability control and transmission shift points\u003c\/p\u003e\n\u003cp\u003eSteering Stabilizer: The HD60 Ram assist bracket requires an aftermarket stud style trac bar bolt to accommodate a steering stabilizer. Trac bar bolts are available from FOX Racing P\/N 803-02-028 or Synergy Manufacturing P\/N 8806-01\u003c\/p\u003e\n\u003ch4\u003eSpecifications\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eRatio:\u003c\/strong\u003e 4.88\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSpline Count:\u003c\/strong\u003e 35\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTubing Diameter:\u003c\/strong\u003e 3.50in\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWidth:\u003c\/strong\u003e 68in\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eWarranty:\u003c\/strong\u003e 2 Year\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFitment:\u003c\/strong\u003e JT\/JL\u003c\/p\u003e","brand":"Currie Enterprises","offers":[{"title":"Default Title","offer_id":48116223213745,"sku":"CE-LF6400E48","price":6550.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0631\/9004\/0753\/files\/kzbjoknevxig22rzkoh7.jpg?v=1793281833","url":"https:\/\/wp4x4.com\/products\/ce-lf6400e48-currie-enterprises-hd60-high-pinion-front-axle-w-4-88-gears-and-e-lockers","provider":"WP4x4","version":"1.0","type":"link"}